gsgasil.blogg.se - Vortex strikefire 2

#VORTEX STRIKEFIRE 2 DRIVER#
#VORTEX STRIKEFIRE 2 FULL#

Canadian customers may visit for customer service information. Call Vortex Optics at 80 for prompt, professional, and friendly service. Rest assured that in the event your StrikeFire II becomes damaged or defective, Vortex Optics will repair or replace the red dot at no charge to you. That’s why Vortex products are unconditionally guaranteed and we make this Very Important Promise to you-a Very Important Person. We build optics based on our commitment to your absolute satisfaction. Storage and use in extreme cold will shorten battery life.Avoid storage in direct sunlight or in any very hot location.Remove the battery when putting in storage for extended periods.Keep lens covers closed to protect the lenses when not in use. Note: Do not attempt to disassemble any components of the red dot. Using your breath, or a very small amount of water or pure alcohol, can help remove stubborn things like dried water spots.Īll components are permanently lubricated, so no additional lubricant should be applied.Be sure to blow away any dust or grit on the lenses prior to wiping the surfaces.When cleaning the lenses, be sure to use products that are specifically designed for use on coated optical lenses such as the Vortex Lens Pen and FogFree Cleaning Kits. The exterior of the red dot may be cleaned by wiping with a soft, dry cloth. The Vortex StrikeFire II requires very little routine maintenance other than to periodically clean the exterior lenses. Note: Our Troubleshooting Guide is available online at /content/troubleshooting. Many times, problems thought to be with the scope are actually mount problems. You should not be able to twist or move the StrikeFire in any direction. Is the battery cover loose? Be sure cover is snug and contact points are clean.īe sure all mount screws are tight.Is the battery installed correctly? Be sure the battery is oriented with the “ –” lettering facing the cover.Please check the following before returning a scope for service. Vortex StrikeFire II Red Dot Troubleshooting As long as you can see the dot, you’ll hit your target!

#VORTEX STRIKEFIRE 2 FULL#

The key thing to remember when shooting with the StrikeFire II red dot is to keep both your eyes open! Shooting with both eyes open allows you to take full advantage of your peripheral vision to get on target very quickly. Fire a final three-shot group to confirm proper adjustment.Using arrows for reference, adjust dials in the direction you wish the group to move. Using the center of this group as a reference, make any necessary adjustments for windage and elevation correction.

Fire a three-shot group as precisely as possible.

If necessary, adjust the dot to put you near the center of the target (see Windage and Elevation Adjustment on page 6).

After the StrikeFire has been bore sighted, fire a shot or two at your desired zero distance to check that you’re roughly on target.

With the bulls eye centered in the bore, make windage and elevation adjustments until the illuminated dot is also centered over the bulls eye.įinal sight-in should be done at the range using the exact ammunition you expect to hunt or shoot with:.

Sight through the bore and center the target inside the barrel.

Place the rifle solidly on a rest and remove the bolt.

This can be done using a bore sighter according to the manufacturer’s instructions or by removing the bolt on some rifles to visually sight through the barrel. Sighting in Bore SightingĪfter mounting, an initial bore sighting of the StrikeFire II at short range (25–50 yards) will save time and money at the range. Note: It is a good practice to check mounting and base screws regularly to be sure they haven’t loosened under field conditions.

#VORTEX STRIKEFIRE 2 DRIVER#

We suggest using a torque driver to properly mount your riflescope Once the screws are tightened, the StrikeFire II should not move on the rail/base. Tighten ring cap screws evenly until all are snug- use caution so as not to over-tighten. Position the upper ring mount cap on top of red dot, align screw holes and insert the ring cap screws.

Place the StrikeFire II on the lower half of the ring mount with the adjustment control buttons facing the shooter.

Then, firmly tighten the base clamp hex nut. Press downward and forward toward the muzzle.

Be sure the base clamp is hooked around the outside of the rail/base.

To prevent recoil injury, position the ring so that you have at least four inches of eye relief. Then, attach the lower half to the rail/base and make sure this is solidly seated in the base groove. Separate the upper ring mount cap from the lower half of the ring mount.